Start from the symptom
Viking dishwasher will not start.
Viking's chart gives five checks for a dishwasher that will not start: the door is ajar, DELAY START is on, the water supply is off, the power cord is unplugged, or a household fuse or breaker has gone. If a cycle starts and stops, a Fill Timeout code points to the water supply.

Start with safe observations.
Turn the appliance off and unplug it before any check you can make yourself. Beware of standing water and sharp edges. Never touch a wet plug or live wiring, take off service panels, or go beyond what your series' guide allows.
- 1
Close the door firmly
The first cause listed is a door that is ajar. Make sure it is closed securely.
- 2
DELAY START
Make sure the DELAY START option is not turned on.
- 3
Water supply
Check that the water supply is connected properly and the water is turned on.
- 4
Power
Confirm the cord sits in the wall socket, then look at the fuse box for a blown fuse or a tripped breaker.
- 5
Start sequence
Buttons light only after you select them. Select START, then shut the door inside 4 seconds.
- 6
Fill Timeout 2-2
Code 2-2 means the dishwasher did not fill in time. Check the supply is on, the fill line is not kinked, the unit is level, and the sink tap pressure has not dropped. Reset and try again.
- 7
Interrupted cycle
If a cycle was interrupted, the Start/Resume and Power On LEDs flash.
Systems a technician may investigate.
Which part is needed gets decided on site, once the label is read and the diagnostic is done. We buy nothing in advance, and you say yes to the price before the work starts.

Filters and the coarse strainer
A Viking 451 or 324 Series dishwasher keeps a coarse strainer, a fine filter and a primary filter in its base, under the lower rack. Viking says never to run the machine without the filters in place. You lift out and empty the strainer, can twist out the fine filter, and should leave the primary filter alone.

Drain hose and high loop
The drain hose carries wash water out of a Viking built-in dishwasher toward the plumbing under your sink. The 451 Series chart lists a clogged or kinked hose when the machine will not drain, and asks for a cone fitting cut to an inner diameter of at least 3/4 inch. The 324 Series chart adds a high loop.
Read the related care guide.

Water left in your Viking dishwasher? Check the strainer and hose.
On a Viking 451 or 324 Series dishwasher, standing water after a finished cycle is a drain problem, and the manuals list the checks in order: a closed door and power, a clean coarse strainer and filters, a drain hose that is not kinked or blocked, a disposal plug that has been removed, a high loop in the hose, and a level machine. Hold START for four seconds to reset. [1][2]

Pots/Pans or Normal Wash? Pick the right Viking cycle.
A Viking dishwasher picks the wash from five cycles on the 451 Series or four on the 324 Series: Pots/Pans for baked-on soil, Normal Wash for everyday loads, Light/China for delicate items, Fast Wash on the 451 only, and Rinse/Hold with no heat. Options such as Hi Temp Wash and Sanitized 155 F Rinse work only with Pots/Pans and Normal Wash. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
All five checks pass and the dishwasher still will not start.
A 2-2 pattern returns after a reset and a water check.
Arrange a diagnosticSources and model boundaries.
The Viking dishwasher will not start guidance rests on these references. Choose the manual that fits your own series.
- Viking Use & Care Manual / 451 Series Built-In Dishwashers
- Use & Care / 324 Series Built-In Dishwashers
Rely on the guide for your precise series, and read how we research these pages.
What are Viking's causes for a dishwasher that will not start?
The door is ajar, DELAY START is on, the water supply is disconnected or off, the power cord is unplugged, or the household fuse or breaker has gone.
What is code 2-2 on a Viking dishwasher?
It is Fill Timeout: check the water supply is on, the fill line is not kinked, the unit is level, and sink water pressure has not dropped. Reset and try again.
Will a cycle start after a power cut?
The chart does not say. Check the cord and breaker, select START and shut the door inside 4 seconds, the printed sequence.
Could the latch be the cause?
The chart lists only an ajar door. It has no latch entry, so a door that refuses to shut fully needs a technician to look at it.
Viking codes, symptoms, parts, visits
From the message to your next move.
2-2
2-2 means the POTS/PANS light flashes twice and the NORMAL WASH light flashes twice. Viking's chart calls it Fill Timeout and lists four checks: supply on, fill line not kinked, dishwasher level, and water pressure at the sink.
Viking dishwasher not cleaning well
A Viking dishwasher that leaves dishes dirty or cloudy is, per Viking's chart, mostly a loading, detergent or filter matter. Check the filters and strainer first, then the wash arms, rinse agent and detergent amount. Odor and slow drying have their own entries, covered below.
Dishwasher repair
Book a diagnostic for your series at the appliance itself.
Find your metro
Office particulars and the entry details to give us.