Viking ice maker ICE and DRAIN lamps blinking / Temperature sensors

Viking ice-maker
error ICE and DRAIN lamps blinking

Ice-maker / display referenceICE and DRAIN lamps blinking

When the ICE and DRAIN lamps blink together on a Viking FNIU515D, the sensor reading air ahead of the condenser is open or shorted. That is the chart’s reading. Nothing in the guide suggests a home fix, so book a visit.

Also shown as ICE and DRAIN lamps blinking

Last reviewed

Ice-maker / display referenceICE and DRAIN lamps blinking
Meaning
When the ICE and DRAIN lamps blink together on a Viking FNIU515D, the sensor reading air ahead of the condenser is open or shorted. That is the chart’s reading. Nothing in the guide suggests a home fix, so book a visit.
Who handles it
Book a visit
Related codes
Source
Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

What Viking ice maker ICE and DRAIN lamps blinking means.

What it means

When the ICE and DRAIN lamps blink together on a Viking FNIU515D, the sensor reading air ahead of the condenser is open or shorted. That is the chart’s reading. Nothing in the guide suggests a home fix, so book a visit.

What you can safely check

Only ICE and DRAIN should blink, with NO WATER dark.

When to call a technician

The two lamps come back after you restart the machine.

Your Viking checklist, kept on this device only

Safe checks, in order.

0 of 4 checks done
  1. Viking ice maker ICE and DRAIN lamps blinking: Undercounter ice machine with its front panel off and plug on the floor, a gloved finger pointing at a thin sensor on the evaporator above the ice bin
    Illustration. Follow your model’s instructions.
    Before you begin

    Match the lamps

    Only ICE and DRAIN should blink, with NO WATER dark. Three lamps blinking at once is a different row of the chart, and so is a lone ICE lamp.

  2. Ice makers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Check the kitchen air

    The sensor reads the air in front of the condenser. Make sure the grille is clear and nothing is stacked against the front of the machine.

  3. Heavy metal control knobs on a professional-style range
    Illustration. Follow your model’s instructions.
    Check 3

    Cycle the power once

    Set the mode switch to off, pull the plug for about sixty seconds, then restore power and select ice. A sensor lead that is truly open or shorted brings the lamps right back.

  4. A technician holds a tablet showing a blank checklist beside a stainless gas range with a skillet on a lit burner.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    Nothing is printed under the action column for this row. Testing or swapping a sensor means taking off the lower panel with the machine unplugged, so it goes on our technician’s list.

Still showing ICE and DRAIN lamps blinking?

Pass along the model and the checks you ran, then open a visit request from this spot.

Book a visit

Ice maker cycle.

Conceptual Ice maker sectionWater inletEvaporator plateIce bin and bin sensorDrain pumpControl12345
  1. 1Water inlet
  2. 2Evaporator plate
  3. 3Ice bin and bin sensor
  4. 5Control

A simplified sketch, because the inside of a Viking differs by series. Tap a highlighted part for its photo and the matching test.

A little more context.

Which sensor does this pattern point to?

The air temperature sensor that sits ahead of the condenser. When that sensor is disconnected or shorted, the chart assigns the ICE and DRAIN blink.

Read the supporting manual

Is the machine broken or only warning me?

The chart files it as a sensor error, not a reminder. With no action printed beside it, the display gives you no route to clear it yourself.

Read the supporting manual

Which lamp pairs belong to the other two sensors?

Each sensor row has its own pair of lamps. ICE with NO WATER is the evaporator sensor, and NO WATER with DRAIN is the ice full sensor in the bin.

Read the supporting manual

What is worth trying before a visit?

Make sure the front grille is open and the room is at normal kitchen temperature, restart once, and stop there. Everything past the panel is service work.

Read the supporting manual

The manual behind the message.

Manufacturer document

Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

Viking Range, LLC (official manual PDF)

Rev C, printed code (051525) / PDF p.17

Taken from the lamp chart in the owner’s guide for the 15 in panel-ready FNIU515D nugget model with a drain pump.

Here to help

Good questions.
Clear answers.

Talk to our team
Which lamps blink for the air temperature sensor?

ICE and DRAIN blink together while NO WATER stays off. On the FNIU515D chart that pairing belongs to the air temperature sensor row.

Will the ice machine make ice while this shows?

No figure is given for that. Assume ice output is unreliable until the sensor is sorted, and check the bin before you host.

Is a cold room the cause?

Not by the chart. Room temperature is named only in the freezing row, so a chilly kitchen is worth noting but is not the stated trigger here.

Is the sensor something I can swap?

The guide offers no owner replacement. It sits behind the lower panel near the refrigeration parts, which our technicians handle.

Let’s take care of it.

The burner will not light.
Let us take a look.