Viking dishwasher 1-2 / Flash pairs

Viking dishwasher
error 1-2

Dishwasher / display reference1-2

1-2 means the POTS/PANS light flashes once and the NORMAL WASH light flashes twice. Viking's chart calls it Motor Control Status Error and prints only a reset.

Also shown as 1-2

Last reviewed

Dishwasher / display reference1-2
Meaning
1-2 means the POTS/PANS light flashes once and the NORMAL WASH light flashes twice. Viking's chart calls it Motor Control Status Error and prints only a reset.
Who handles it
Reset, then book
Related codes
Source
Viking Use & Care Manual / 451 Series Built-In Dishwashers

What Viking dishwasher 1-2 means.

What it means

1-2 means the POTS/PANS light flashes once and the NORMAL WASH light flashes twice. Viking's chart calls it Motor Control Status Error and prints only a reset.

What you can safely check

One, then two.

When to call a technician

1-2 flashes again after the reset.

Your Viking checklist, kept on this device only

Safe checks, in order.

0 of 4 checks done
  1. Viking dishwasher 1-2: Stainless dishwasher with a closed door, two amber lights lit on the left of the control strip, two green on the right and a small lit display between
    Illustration. Follow your model’s instructions.
    Before you begin

    Count the flashes

    One, then two.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Reset the unit

    Hold START for 4 seconds.

  3. Heavy metal control knobs on a professional-style range
    Illustration. Follow your model’s instructions.
    Check 3

    Run a short cycle

    Watch for the pair.

  4. A technician holds a tablet showing a blank checklist beside a stainless gas range with a skillet on a lit burner.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    The chart lists no owner checks.

Still showing 1-2?

Pass along the model and the checks you ran, then open a visit request from this spot.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 2Control board
  2. 3Motor wiring
  3. 4Heater wiring

A simplified sketch, because the inside of a Viking differs by series. Tap a highlighted part for its photo and the matching test.

A little more context.

What does the chart print for 1-2?

Motor Control Status Error, the second row of the group where POTS/PANS flashes once. The only action printed is to reset the unit and try again.

Read the supporting manual

How does 1-2 differ from 1-3 and 3-4?

1-2 and 1-3 both name the motor control: Status Error in one, Comms Error in the other. 3-4 is labeled only Motor Status. The chart separates them by label and gives no further detail.

Read the supporting manual

What will I notice at the dishwasher?

The manual says to turn to its chart in the troubleshooting section when the cycle buttons are flashing. The beep that goes with an error message cannot be turned off, and the LED flashes in step with it.

Read the supporting manual

The manual behind the message.

Manufacturer document

Viking Use & Care Manual / 451 Series Built-In Dishwashers

Viking Range, LLC (official manual PDF)

form F20879C EN (022213) / PDF p.19

Manufacturer document

Use & Care / 324 Series Built-In Dishwashers

Viking Range, LLC (official manual PDF)

form F21216 EN (060113) / PDF p.18

Sources: the Viking 451 Series (p. 19) and 324 Series (p. 18) built-in dishwasher manuals; both print the same flash chart.

Here to help

Good questions.
Clear answers.

Talk to our team
Which motor does the control report on?

The chart does not name it. It prints only the label Motor Control Status Error, so treat the motor as unidentified until a technician tests it.

Can I silence the beeping while it shows?

No. The manual states the audible sound cannot be disabled for error messages, although the Rinse/Hold beep setting can be turned off for normal use.

Is 1-2 the same on the 451 and 324 Series?

Yes. Both manuals print 1-2 as Motor Control Status Error with the same reset action. Only the Fill Too Fast row moves between the two charts.

Should I keep running cycles to see if it clears?

One reset and one test cycle matches the chart. If the same pair flashes again, further cycles tell you nothing new, so book a visit.

Let’s take care of it.

The burner will not light.
Let us take a look.