Start from the symptom

Viking range burner will not light.

A Viking range burner that will not light usually comes down to power, the gas valve, or a dirty igniter. Viking's printed table separates the causes by what you see: no spark, spark but no flame, endless sparking, or a yellow flame. With a gas smell, leave the knobs alone and phone your gas supplier.

Last reviewed

A stainless range with a sealed burner cap showing no flame, a cast iron grate lifted off and set on the counter, and a stockpot standing behind it.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Start with safe observations.

Turn the appliance off and unplug it before any check you can make yourself. Beware of standing water and sharp edges. Never touch a wet plug or live wiring, take off service panels, or go beyond what your series' guide allows.

  1. 1

    Gas smell: stop before anything else

    The range manual's gas-smell list: light no appliance, flip no electrical switch, use no phone in the building. Ring the gas supplier on a neighbor's line, or the fire department if you cannot.

  2. 2

    No spark at all

    The table lists three causes for igniters that do nothing: a tripped circuit, a blown fuse, or a range that is not connected to power. Check the breaker before you assume the igniter has failed.

  3. 3

    Clicking but no flame

    Two causes are printed: the gas supply valve is in the OFF position, or the gas supply has been interrupted. Both sit outside the range, so check the valve and whether other gas appliances are working.

  4. 4

    Sparking that will not stop

    After the flame lights, constant sparking points to a power supply that is not grounded, reversed polarity, or igniters that are wet or dirty. Dry the igniter area and wipe the burner cap clean.

  5. 5

    Large, distorted or yellow flame

    Viking lists clogged burner ports, the wrong type of gas, and air shutters that are not adjusted. Clean ports only with a straight pin, and never enlarge them or use a toothpick.

  6. 6

    Seat the cap and head correctly

    The manual says clean burner caps keep ignition and flames even. When refitting a head, keep its two underside tabs clear of the igniter and make sure the cap sits level.

  7. 7

    Red backlight on a 7 Series

    On a 7 Series range with backlit knobs, an error shows as a red backlight and flashing knob rings. The guide prints no table for it, so note how the rings flash and book a visit.

When observation becomes a service request.

Leave internal testing to a technician.

A gas smell, or the burner will not light after the breaker and gas valve check out.

The flame stays yellow or distorted after you have cleaned the cap, head and ports.

Sparking continues, or a grounding or polarity cause is suspected. Both call for someone qualified.

Arrange a diagnostic

Sources and model boundaries.

The Viking range burner will not light guidance rests on these references. Choose the manual that fits your own series.

  • Use & Care / 3 Series / Freestanding 30” Gas / Self-Clean Sealed Burner Range
  • Use & Care / Professional Freestanding Ranges / Built-In Rangetops

Rely on the guide for your precise series, and read how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
What does the manual say to do if I smell gas near my Viking range?

Light nothing, flip no switch and use no phone in the building. Phone the gas supplier from a neighbor's home, or the fire department if you cannot reach them. Gas parts are for qualified people.

Why does one burner click but never catch?

Viking's table gives two causes for sparking with no flame: the gas valve is off, or the gas supply is interrupted. Check both before suspecting the igniter.

What can I use on clogged burner ports?

A straight pin. The manual says not to enlarge or distort the ports, and it rules out a toothpick.

Is a yellow flame always a sign of a dirty burner?

Not always. Besides clogged ports, the table lists the wrong type of gas and air shutters that are not set properly. Those last two need a technician.

Do I need a technician for constant sparking?

If wiping and drying the igniter area does not stop it, yes. A missing ground or reversed polarity are also on Viking's list, and neither is a job for a home cook.

Let’s take care of it.

The burner will not light.
Let us take a look.