Start from the symptom
Viking dishwasher leaking.
The Viking dishwasher manuals print no leak entry in their troubleshooting chart. What they do print is PAN FLOOD: both cycle lights flash continuously, and the chart's only action is to reset by holding START for 4 seconds. Water on the floor calls for the supply shut and a visit, not repeated resets.

Start with safe observations.
Turn the appliance off and unplug it before any check you can make yourself. Beware of standing water and sharp edges. Never touch a wet plug or live wiring, take off service panels, or go beyond what your series' guide allows.
- 1
Stop and shut off
If water is escaping, stop the cycle, close the water supply and switch off the dishwasher's breaker. That is our safety advice; the manual lists no leak step.
- 2
PAN FLOOD
Both lights flash continuously (Note A). Viking's chart prints one action: reset the unit and try again. If the problem persists, contact service.
- 3
1-1 Pan Flood Sensor Disconnect
One flash of POTS/PANS and one of NORMAL WASH means the pan flood sensor is disconnected. The chart gives the same reset action.
- 4
Drain checks
For Drain Error (1-5), verify the drain hose is not clogged or kinked, the high loop is per the installation guide, the unit is level and the filters are clear.
- 5
High Level Error 2-4
Verify items in the rack are retained so they cannot turn over.
- 6
Wipe up and document
Dry the floor and note when the water appeared, which cycle was running and any flashing pattern.
Systems a technician may investigate.
The parts below connect to this symptom. Seeing it does not establish that any one of them is the culprit.
If the display adds a code.
Flash pairs
1-1 means the POTS/PANS light flashes once and the NORMAL WASH light flashes once. Viking's chart calls it Pan Flood Sensor Disconnect and prints only a reset: hold START for 4 seconds.
Flash pairs
1-5 means the POTS/PANS light flashes once and the NORMAL WASH light flashes five times. Viking's chart calls it Drain Error and lists six checks: sink, drain hose, disposal plug, high loop, level and filters.
Read the related care guide.

Water left in your Viking dishwasher? Check the strainer and hose.
On a Viking 451 or 324 Series dishwasher, standing water after a finished cycle is a drain problem, and the manuals list the checks in order: a closed door and power, a clean coarse strainer and filters, a drain hose that is not kinked or blocked, a disposal plug that has been removed, a high loop in the hose, and a level machine. Hold START for four seconds to reset. [1][2]

Pots/Pans or Normal Wash? Pick the right Viking cycle.
A Viking dishwasher picks the wash from five cycles on the 451 Series or four on the 324 Series: Pots/Pans for baked-on soil, Normal Wash for everyday loads, Light/China for delicate items, Fast Wash on the 451 only, and Rinse/Hold with no heat. Options such as Hi Temp Wash and Sanitized 155 F Rinse work only with Pots/Pans and Normal Wash. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
Water appears on the floor or inside the base, or PAN FLOOD returns after a reset.
You are unsure where the water is coming from.
Arrange a diagnosticSources and model boundaries.
The Viking dishwasher leaking guidance rests on these references. Choose the manual that fits your own series.
- Viking Use & Care Manual / 451 Series Built-In Dishwashers
- Use & Care / 324 Series Built-In Dishwashers
Rely on the guide for your precise series, and read how we research these pages.
What does PAN FLOOD mean on a Viking dishwasher?
Both cycle lights flash continuously (Note A). The chart's action is to reset the unit by holding START for 4 seconds and try again, then contact service if it persists.
Is there a leak entry in Viking's troubleshooting chart?
Not in the 451 or 324 Series manuals. The nearest entries are PAN FLOOD and 1-1 in the flash-code chart, so those carry this page.
Should I run the dishwasher again after a leak?
Not until the source is found. Reset once to read the code, and keep the supply closed. A cycle with water escaping risks the cabinet base and the floor.
Can a bad drain hose cause a leak?
The chart lists a clogged or kinked drain hose under Drain Error, and asks for a high loop and a level dishwasher. It does not say the hose leaks, so a technician should trace the water.
Viking codes, symptoms, parts, visits
From the message to your next move.
PAN FLOOD
PAN FLOOD on a Viking built-in dishwasher is shown by both lights, POTS/PANS and NORMAL WASH, flashing continuously. Viking prints only a reset: hold START for 4 seconds. If water reaches the floor, shut the supply valve and book a technician.
Viking dishwasher not cleaning well
A Viking dishwasher that leaves dishes dirty or cloudy is, per Viking's chart, mostly a loading, detergent or filter matter. Check the filters and strainer first, then the wash arms, rinse agent and detergent amount. Odor and slow drying have their own entries, covered below.
Drain hose and high loop
The drain hose carries wash water out of a Viking built-in dishwasher toward the plumbing under your sink. The 451 Series chart lists a clogged or kinked hose when the machine will not drain, and asks for a cone fitting cut to an inner diameter of at least 3/4 inch. The 324 Series chart adds a high loop.
Dishwasher repair
Book a diagnostic for your series at the appliance itself.
Find your metro
Office particulars and the entry details to give us.
