Inside the appliance
Water level sensors. In plain English.
A Viking 451 or 324 Series dishwasher watches the water level in the tub. A Low Level Sensor Error is 2 flashes of POTS/PANS then 3 of NORMAL WASH, and a High Level Error is 2 then 4. The chart lists dishes tipped over and holding water, the drain hose loop, and loose items in the racks.

Where it fits.
Water level sensors in the appliance
Inside the tub; the unit shows its result on the POTS/PANS and NORMAL WASH lights.
The photo shows the kind of component. It cannot tell you which replacement fits your series.
The signs that this system wants attention.
Water level sensors trouble can turn up together with a drop in performance or a code that keeps coming back. Testing is required before anyone decides this component is to blame.

Viking dishwasher not cleaning well
A Viking dishwasher that leaves dishes dirty or cloudy is, per Viking's chart, mostly a loading, detergent or filter matter. Check the filters and strainer first, then the wash arms, rinse agent and detergent amount. Odor and slow drying have their own entries, covered below.

Viking dishwasher controls not responding
On a Viking 451 or 324 Series dishwasher, a dark panel is often normal: cycle and option buttons only light after you select them. Select START, shut the door inside 4 seconds, and the cycle begins. If the lights flash instead, use the reset: hold START for 4 seconds.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can make yourself. Beware of standing water and sharp edges. Never touch a wet plug or live wiring, take off service panels, or go beyond what your series' guide allows.
- 1
Look for tipped-over dishes
For 2-3, make sure no dishes have turned over and are holding a significant amount of water.
- 2
Check the drain hose high loop
The chart asks you to confirm the drain hose has the high loop shown in the installation guide.
- 3
Check the racks
For 2-4, verify items in the rack are retained so that they cannot turn over.
- 4
Reset and retry
Press START and keep it down 4 seconds to reset the unit, then run it again.
Cleaning or replacement?
Leave internal testing to a technician.
2-3 or 2-4 returns after a reset with the racks loaded properly.
Water stays in the tub when the cycle ends.
Arrange a diagnosticSources and model boundaries.
The Water level sensors guidance rests on these references. Choose the manual that fits your own series.
- Use & Care Manual, 324 Series Built-In Dishwashers (F21216)
Rely on the guide for your precise series, and read how we research these pages.
What does 2-3 mean?
Two flashes of the POTS/PANS light and three of NORMAL WASH. Viking's chart names it Low Level Sensor Error.
What does 2-4 mean?
Two flashes of POTS/PANS and four of NORMAL WASH. The chart names it High Level Error.
How is the unit reset?
Keep START pressed for 4 seconds, then try the cycle again.
Do these checks apply to both series?
These pairs come from the 324 Series chart. For a 451 Series, read your own manual.
Viking codes, symptoms, parts, visits
From the message to your next move.
2-3
2-3 means the POTS/PANS light flashes twice and the NORMAL WASH light flashes three times. Viking's chart calls it Low Level Sensor Error and lists two checks: dishes holding water, and the drain hose high loop.
Viking dishwasher not cleaning well
A Viking dishwasher that leaves dishes dirty or cloudy is, per Viking's chart, mostly a loading, detergent or filter matter. Check the filters and strainer first, then the wash arms, rinse agent and detergent amount. Odor and slow drying have their own entries, covered below.
Dishwasher repair
Book a diagnostic for your series at the appliance itself.
Find your metro
Office particulars and the entry details to give us.

