Viking ice maker ICE and NO WATER lamps blinking / Temperature sensors

Viking ice-maker
error ICE and NO WATER lamps blinking

Ice-maker / display referenceICE and NO WATER lamps blinking

A Viking FNIU515D that blinks ICE and NO WATER in step is pointing at the evaporator outlet sensor, which the chart calls disconnected or shorted. Its action: check the sensor and how it is attached, then restart after the repair.

Also shown as ICE and NO WATER lamps blinking

Last reviewed

Ice-maker / display referenceICE and NO WATER lamps blinking
Meaning
A Viking FNIU515D that blinks ICE and NO WATER in step is pointing at the evaporator outlet sensor, which the chart calls disconnected or shorted. Its action: check the sensor and how it is attached, then restart after the repair.
Who handles it
Book a visit
Related codes
Source
Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

What Viking ice maker ICE and NO WATER lamps blinking means.

What it means

A Viking FNIU515D that blinks ICE and NO WATER in step is pointing at the evaporator outlet sensor, which the chart calls disconnected or shorted. Its action: check the sensor and how it is attached, then restart after the repair.

What you can safely check

ICE and NO WATER blink while DRAIN stays dark.

When to call a technician

The two lamps are back once the machine has been restarted.

Your Viking checklist, kept on this device only

Safe checks, in order.

0 of 4 checks done
  1. Viking ice maker ICE and NO WATER lamps blinking: Undercounter ice machine with its front panel off and plug on the floor, a gloved finger pointing at a thin sensor on the evaporator above the ice bin
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the lamps again

    ICE and NO WATER blink while DRAIN stays dark. If DRAIN joins in, you are on the Er01 evaporator temperature row instead.

  2. Ice makers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Let it rest

    Leave the mode switch on off for a short spell, then go back to ice. That can clear a stray reading, though it cannot repair a sensor that is genuinely open.

  3. Heavy metal control knobs on a professional-style range
    Illustration. Follow your model’s instructions.
    Check 3

    Do not chase it with water checks

    Here the NO WATER lamp is just one half of the pattern. It does not say the supply line is shut, so skip the valves and filters.

  4. A technician holds a tablet showing a blank checklist beside a stainless gas range with a skillet on a lit burner.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    The chart asks for a check of the sensor and its attachment and a restart after the sensor part is repaired. That means panel-off work on the evaporator side.

Still showing ICE and NO WATER lamps blinking?

Pass along the model and the checks you ran, then open a visit request from this spot.

Book a visit

Ice maker cycle.

Conceptual Ice maker sectionWater inletEvaporator plateIce bin and bin sensorDrain pumpControl12345
  1. 1Water inlet
  2. 2Evaporator plate
  3. 3Ice bin and bin sensor
  4. 5Control

A simplified sketch, because the inside of a Viking differs by series. Tap a highlighted part for its photo and the matching test.

A little more context.

What is the EVA sensor?

The thermistor at the evaporator outlet. This lamp pairing is reserved for the moment it is found disconnected or shorted.

Read the supporting manual

What action does the chart print?

Two things: check the sensor and its attachment for abnormality, then start operation after the sensor part is repaired.

Read the supporting manual

Why does NO WATER blink when the water is fine?

The lamps act as a code. The chart reads the combination rather than each lamp alone, so a full reservoir does not rule the pattern out.

Read the supporting manual

Could it be one of the Er01 or Er03 rows?

No. Those rows describe the evaporator staying at 32 F or warmer, and Er01 blinks all three lamps. This row is about the sensor reading itself.

Read the supporting manual

The manual behind the message.

Manufacturer document

Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

Viking Range, LLC (official manual PDF)

Rev C, printed code (051525) / PDF p.17

FNIU515D guide, page 17 lamp chart: the evaporator-sensor pairing.

Here to help

Good questions.
Clear answers.

Talk to our team
Does NO WATER blinking with ICE mean the supply is off?

Not in this pairing. Read the two lamps as one signal that names the evaporator sensor, and leave the water line alone.

Where is the evaporator sensor?

At the evaporator outlet inside the cabinet. No owner access is shown anywhere in the guide.

Can the machine stay on meanwhile?

No guidance is printed. The sensor watches the cooling cycle, so switch the machine off while the pattern is lit and nobody is nearby.

Will pulling the plug clear it?

Only a stray reading. If the sensor really is open or shorted, the lamps reappear as soon as the machine tries to make ice.

Let’s take care of it.

The burner will not light.
Let us take a look.