Using your appliance

Viking dishwasher beeps and how to mute or reset them

A Viking dishwasher gives one beep for a key press, three short beeps when START was not pressed or the door was not closed within 4 seconds, and two long beeps when the cycle ends. Hold Rinse/Hold for 10 seconds to mute the cycle sounds. Error beeps cannot be muted, and holding START for 4 seconds resets the unit. [1][2]

A fingertip reaches toward one softly lit button on the top edge of an open dishwasher door.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • One beep means a cycle, an option or START was pressed. 12
  • Three short beeps mean START was not pressed or the door was not closed within 4 seconds. 12
  • Two long beeps are the end-of-cycle signal; on the 324 Series it sounds 30 minutes after the last drain. 12
  • Hold Rinse/Hold for 10 seconds to turn the audible sound off or on. 12
  • Error beeps cannot be disabled, and a reset is a 4 second hold of START. 12

What do the beeps on a Viking dishwasher mean?#

One beep acknowledges a key, three short beeps mean the cycle never began, and two long beeps end a cycle. The manuals for the 451 and 324 Series print these three signals under Audible Sound Signal, and a fourth group, error messages, in the flash code chart. 12

SoundMeaningYour move
One beepYou selected a cycle or option, or pressed STARTNothing; this is the key tone
Three short beepsSTART was not pressed, or the door stayed open past 4 seconds after pressing itPress START again and shut the door until it clicks
Two long beepsEnd of cycleOpen the door when the cycle is complete
Beeps with flashing cycle lightsAn error messageUse the flash code chart, hold START 4 seconds to reset

The tone is part of the way the dishwasher talks. It has no display with words, only lit buttons, so the sound and the lights together give the full message. The signals sit next to the cycle descriptions in the controls chapter, and our cycles guide explains the buttons that go with them. 12

Why do I hear three short beeps?#

The dishwasher is telling you it did not start. Either START was not pressed after you chose a cycle, or the door was not closed within 4 seconds of pressing START. The manuals call this three short beeps in the audible sound signal entry. 12

Start the sequence over. After you select the cycle and options, press START, watch the START symbol light, and close the door firmly until you hear a click within 4 seconds. The manuals note that the symbol lighting only means the machine is ready, and that a door that is not shut firmly keeps the cycle from beginning. 12

  1. 1

    Select the cycle and options#

    The cycle, option and Start buttons light only after you select them. 12

  2. 2

    Press START#

    The START symbol lights to show the machine is ready. 12

    A small glowing triangle symbol shows on the dark control strip of an open dishwasher door.
  3. 3

    Close the door#

    Close it tightly until you hear a click, within 4 seconds of pressing START. 12

  4. 4

    Listen for one beep#

    If you hear three short beeps instead, repeat from the first step. 12

If the sequence is right and the dishwasher still will not run, see the page on a dishwasher that stays idle. The manual's own list is an open door, a Delay Start left on, a disconnected water supply or power cord, and a fuse that has blown or a breaker that has tripped. 1

When does the end-of-cycle signal sound?#

When the cycle is finished, two long beeps sound. On the 451 Series the manual describes the end-of-cycle signal as two long beeps. The 324 Series manual adds that it activates 30 minutes after the last drain, when the condensate dry portion of the cycle is completed. 12

That wait explains an odd experience on the 324 Series: the water stops and the dishwasher goes quiet, yet the end signal sounds only later. The cycle data note says the wash time shown does not include that 30 minute condensate dry. On the 451 Series, the manual notes that AirFlo Gentle Drying adds roughly an hour to the total cycle time. 12

The Start/Resume button blinks if the cycle is interrupted, and on the 451 Series the Power On light under the kickplate blinks too. A blink without an end signal means the cycle did not finish. 12

How do I turn the beeping off?#

Press and hold the Rinse/Hold button for 10 seconds. The beep stops and the Rinse/Hold LED flashes 2 times. To turn the sound back on, repeat the same hold; the dishwasher beeps 2 times and the Rinse/Hold LED flashes 2 times to confirm it is on. 12

  1. 1

    Find the Rinse/Hold button#

    It is on the control strip at the top of the door. 12

  2. 2

    Press and hold for 10 seconds#

    Keep your finger on the button for the full 10 seconds. 12

    A small amber indicator light glows beside a round button on a stainless dishwasher control strip.
  3. 3

    Watch the LED#

    The beep stops and the Rinse/Hold LED flashes 2 times. The audible sound is now off. 12

  4. 4

    To restore it, repeat#

    The dishwasher beeps 2 times and the LED flashes 2 times. 12

Both manuals say the LED flashes in step with the audible sound. If the dishwasher is silent and the LED flashes anyway, that matches the printed behavior. 12

Can I silence the beeps for an error too?#

No. Both manuals state that the audible sound cannot be disabled for error messages. Muting the cycle sounds leaves the error beeps in place, so a beep after muting is a signal you should look at, not one your mute failed to catch. 12

That is also why a quiet dishwasher is not necessarily a healthy one. Check the lights. The flash code chart counts the flashes of the Pots/Pans and Normal Wash lights, so, for example, one flash and then five flashes is the drain error. 12 The chart is in our dishwasher error code library, and the pan flood entry covers the case when both lights flash continuously.

How do I reset a Viking dishwasher?#

Press and hold START for 4 seconds. The flash code chart's Note B says this resets the unit, and every row in the chart tells you to reset the unit and try again before you call for service. If the problem persists, the chart says to contact service. 12

The same notes explain the flash code format: the numbers listed are the times the lights will flash, so a drain error means the POTS/PANS light flashes once and the NORMAL WASH light flashes 5 times. And the cycle and option keys light only after they are selected, so a dark panel before you press START is normal. 12

What do the lights do besides blinking?#

The Start/Resume button blinks when a cycle is interrupted. The Sanitized indicator lights when a cycle finishes with a sanitizing rinse, and stays dark when the cycle was interrupted or the water did not reach the required temperature; it clears after you open and close the door. 12

On the 451 Series, a blue Power On light shines at the bottom middle of the kickplate while a cycle runs. It blinks when a cycle is interrupted. 1 The 324 Series manual notes the Start/Resume button flashes when the cycle is interrupted and does not describe the Power On light. 2

Which sounds are normal during a wash?#

Water, pump and spray sounds are expected in any dishwasher. The manuals' troubleshooting charts list one noise issue: unusual noise from utensils that may not be secure or that dropped from a rack, where water makes them rattle. Make sure everything is securely placed. 1

A rattle is a loading issue, while a beep is a signal from the controls. Do not mix the two when you describe the problem on a call.

Our dishwasher repair page shows what a technician does at the door. If the controls seem dead rather than noisy, see Viking dishwasher controls not responding.

What do I report about the beeping?#

Describe the sound, the lights and what you did. A phone recording of the beeps helps.

  • How many beeps, and were they short or long?
  • Which lights flashed, and how many times in a row?
  • Did the reset (START held 4 seconds) change anything?
  • Is the dishwasher a 451 or 324 Series (the cover of your manual says)?

Sources#

  1. Use & Care Manual, 451 Series Built-In DishwashersViking Range Corporation (official manual PDF) · form F20879C EN (022213) · PDF p.6 (Audible Sound Signal), p.19 (flash code, Notes B-D, Turning Audible Sound On and Off)
  2. 324 Series Built-In Dishwashers Use & CareViking Range, LLC (official manual PDF) · form F21216 EN (060113) · PDF p.6 (Audible Sound Signal), p.18 (flash code, Notes B-D, Turning Audible Sound On and Off)

Here to help

Good questions.
Clear answers.

Talk to our team
Why did my Viking dishwasher beep three times?

Three short beeps mean START was not pressed, or the door stayed open past 4 seconds after pressing it. Press START again and close the door firmly until it clicks. [1][2]

What does one beep mean?

A single beep sounds when you select a cycle or an option and when you press START. It is the normal key tone, not an alert. [1][2]

What does the end-of-cycle signal sound like?

Two long beeps. On the 324 Series it sounds 30 minutes after the last drain, once the condensate dry portion of the cycle is complete. [1][2]

How do I turn the beeping off?

Press and hold Rinse/Hold for 10 seconds. The beep stops and the Rinse/Hold LED flashes 2 times. Repeat the same hold to turn the sound back on. [1][2]

Can I silence the beeps that come with an error?

No. The manuals say the audible sound cannot be disabled for error messages, even after you have turned the cycle beeps off. [1][2]

Let’s take care of it.

The burner will not light.
Let us take a look.