Viking ice maker NO WATER and DRAIN lamps blinking / Temperature sensors

Viking ice-maker
error NO WATER and DRAIN lamps blinking

Ice-maker / display referenceNO WATER and DRAIN lamps blinking

NO WATER and DRAIN blinking together on a Viking FNIU515D mean its ice full sensor, down in the storage bin, has lost its connection or shorted out. It is a sensor error, not a water or drain problem. Book a visit.

Also shown as NO WATER and DRAIN lamps blinking

Last reviewed

Ice-maker / display referenceNO WATER and DRAIN lamps blinking
Meaning
NO WATER and DRAIN blinking together on a Viking FNIU515D mean its ice full sensor, down in the storage bin, has lost its connection or shorted out. It is a sensor error, not a water or drain problem. Book a visit.
Who handles it
Book a visit
Related codes
Source
Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

What Viking ice maker NO WATER and DRAIN lamps blinking means.

What it means

NO WATER and DRAIN blinking together on a Viking FNIU515D mean its ice full sensor, down in the storage bin, has lost its connection or shorted out. It is a sensor error, not a water or drain problem. Book a visit.

What you can safely check

NO WATER and DRAIN blink and ICE stays dark.

When to call a technician

NO WATER and DRAIN are blinking again after a power cycle.

Your Viking checklist, kept on this device only

Safe checks, in order.

0 of 4 checks done
  1. Viking ice maker NO WATER and DRAIN lamps blinking: Undercounter ice machine with its front panel off and plug on the floor, a gloved finger pointing at a thin sensor on the evaporator above the ice bin
    Illustration. Follow your model’s instructions.
    Before you begin

    Check which lamps are on

    NO WATER and DRAIN blink and ICE stays dark. A lone blinking ICE lamp is the normal full-bin signal and needs nothing.

  2. Ice makers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Look in the bin

    The ice full sensor lives in the storage bin. If the bin is stuffed with ice or a scoop is wedged in, empty it and see whether the lamps stop. Keep your hands out of any moving parts.

  3. Heavy metal control knobs on a professional-style range
    Illustration. Follow your model’s instructions.
    Check 3

    Restart once

    Turn the mode switch off, wait a minute, then back to ice. A broken lead on the bin sensor will show again as soon as the machine runs.

  4. A technician holds a tablet showing a blank checklist beside a stainless gas range with a skillet on a lit burner.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    The chart prints no action for this row. A technician can check the sensor lead and the connector, which needs the machine unplugged and panels removed.

Still showing NO WATER and DRAIN lamps blinking?

Pass along the model and the checks you ran, then open a visit request from this spot.

Book a visit

Ice maker cycle.

Conceptual Ice maker sectionWater inletEvaporator plateIce bin and bin sensorDrain pumpControl12345
  1. 1Water inlet
  2. 2Evaporator plate
  3. 3Ice bin and bin sensor
  4. 5Control

A simplified sketch, because the inside of a Viking differs by series. Tap a highlighted part for its photo and the matching test.

A little more context.

What does the ice full sensor do?

It tells the machine the bin has filled. When that bin sensor is disconnected or shorted, this is the pattern the chart assigns.

Read the supporting manual

Why do the NO WATER and DRAIN lamps blink?

The chart reads them as a pair, and ties this pairing to the bin sensor rather than to the water inlet or the drain pump.

Read the supporting manual

What does a healthy full bin look like?

One ICE lamp that is lit for two seconds, then dark for one. Per the chart it goes out when the sensor again sees the release temperature.

Read the supporting manual

Is there an owner repair listed?

None. With no action on the row, the bin look and one restart are as far as you go before a visit.

Read the supporting manual

The manual behind the message.

Manufacturer document

Install / Use & Care MANUAL / Undercounter Nugget Ice Machine / FNIU515D

Viking Range, LLC (official manual PDF)

Rev C, printed code (051525) / PDF p.17

Same FNIU515D guide, lamp chart at page 17; the sensor in question sits inside the storage bin.

Here to help

Good questions.
Clear answers.

Talk to our team
Is the drain blocked when DRAIN blinks with NO WATER?

No. A blocked drain is Er16, with its own lamp pattern. With NO WATER and DRAIN blinking together, the chart reads a bin sensor problem.

Could a full bin trigger this?

A full bin shows as the slow ICE blink, not this pair. Still, empty the bin once, because ice jammed against the sensor can confuse the reading.

Is it safe to keep the machine plugged in?

It is low risk, but a machine that cannot tell when the bin is full may overfill or stop. Unplug it if you see ice backing up.

Which lamp stays dark?

In the air sensor row NO WATER is the one left dark; here it is ICE. That single lamp separates the two.

Let’s take care of it.

The burner will not light.
Let us take a look.