Start from the symptom
Viking grill side burner won’t light.
A Viking 5 Series gas side or power burner lights with a hot surface igniter. Push the knob in and hold it 5 to 7 seconds before turning to LITE, and the igniter should glow bright and steady. If it does not, check the GFI outlet, the burner seating and the wind, then book a technician.

Start with safe observations.
Turn the appliance off and unplug it before any check you can make yourself. Beware of standing water and sharp edges. Never touch a wet plug or live wiring, take off service panels, or go beyond what your series' guide allows.
- 1
Pre-light checklist
The guide asks, before each use, whether you smell gas, whether the burners are seated, whether the area is clear and whether the wind is only light. Do these first.
- 2
Push and hold
Make sure all knobs are OFF, push in the knob you want and hold it 5 to 7 seconds while the igniter heats. Then turn to LITE and set the flame.
- 3
Watch the glow
The igniter should glow bright and steady. No glow with the knob pushed in points to the electrical side, not the gas.
- 4
GFI outlet
The ignition runs from an outdoor 120V 15A GFI outlet next to the accessory. The guide says a connection may have come loose in shipping or the GFI may have tripped; reset it.
- 5
Seating and wind
Burners must be seated properly, with the brass peg in the positioning hole. A light breeze is fine; wait if wind blows across the side burner.
- 6
Gas supply
LP units run from a Type 1 cylinder with overfill protection. Check the connection is tight and leak tested, and that the main shut-off valve is open.
Systems a technician may investigate.
The parts below connect to this symptom. Seeing it does not establish that any one of them is the culprit.

Hot surface igniter on side burners
The 5 Series gas side burners and power burner light with a hot surface ignition system. Viking’s guide says to push and hold the control knob for 5-7 seconds so the igniter can heat up, then turn to LITE. During an installation test, the igniter should glow bright and steady.

Gas pressure regulator
A Viking 5 Series outdoor gas side burner, part of the grill family, must run through a pressure regulator. The manual says never connect a gas line directly to the accessory or an unregulated line to the grill. The regulator and orifices match the gas named on the rating plate, and switching gases needs a conversion kit fitted by a qualified technician.

Air shutters and yellow flames
A yellow flame on a Viking side burner means a lack of air, according to the 5 Series side burner guide, though orange tips are normal with dusty air or heavy grease. The fix is to rotate the air shutters, but only after the accessory has cooled completely and all controls are off.
If the display adds a code.
No code is tied straight to this topic.
Nothing else in our researched codes connects to this topic. Match the exact message to your series' manual, and do not swap in another code from the library.
See the research statusFollow the care guide that came with this appliance.
When observation becomes a service request.
Leave internal testing to a technician.
You smell gas. Shut off all burners and the main gas supply, perform a leak test, and call a gas company or a qualified plumber.
The igniter does not glow with power confirmed.
A control knob does not turn freely.
The burner lights only after repeated tries.
Arrange a diagnosticSources and model boundaries.
The Viking grill side burner won’t light guidance rests on these references. Choose the manual that fits your own series.
- User / Install Guide / 5 Series Gas Side Burner Accessories / VQGSB5131 | VQGPB5201
Rely on the guide for your precise series, and read how we research these pages.
How long should the knob stay pressed in?
Hold it in for 5 to 7 seconds while the igniter warms up, as the guide says. Only then turn to LITE and set the flame.
The igniter does not glow. What is wrong?
The guide points to a connection that came loose in shipping or a tripped GFI outlet. Reset the GFI and check the plugs; if it still does not glow, book a technician.
Can wind stop the burner lighting?
The checklist asks whether the wind is only blowing lightly and not on the side burner. If it is not, wait until it subsides before lighting.
Does this apply to the whole grill?
This page covers the 5 Series gas side burner and power burner accessories. The main grill burners have their own manual, which is not in our source set.
Viking codes, symptoms, parts, visits
From the message to your next move.
Viking grill side burner won’t light
A Viking 5 Series gas side or power burner lights with a hot surface igniter. Push the knob in and hold it 5 to 7 seconds before turning to LITE, and the igniter should glow bright and steady. If it does not, check the GFI outlet, the burner seating and the wind, then book a technician.
Hot surface igniter on side burners
The 5 Series gas side burners and power burner light with a hot surface ignition system. Viking’s guide says to push and hold the control knob for 5-7 seconds so the igniter can heat up, then turn to LITE. During an installation test, the igniter should glow bright and steady.
Grill repair
Book a diagnostic for your series at the appliance itself.
Find your metro
Office particulars and the entry details to give us.