Using your appliance

Knob lights on a Viking 7 Series range, decoded

On a Viking 7 Series range or rangetop, each knob ring fades on in white or blue over 2 seconds and fades off over 1 second. Griddle and oven rings pulse during preheat and then hold solid. You choose the color by holding the number 2 button under the bullnose, and the night light switch lights every ring. [1]

A hand turns a range knob ringed in blue light; a cast iron griddle sits over a lit burner.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Burner knob rings fade on over 2 seconds and off over 1 second. 1
  • Griddle and oven rings pulse until the first target temperature and then stay solid. 1
  • Hold the number 2 button to cycle blue, white and off; button 1 is the night light. 1
  • On the griddle, the bezel cycling on and off shows the thermostat holding temperature. 1
  • Red means an error and yellow means self-clean. 1

What do the knob lights do in normal use?#

Each knob has a ring that lights when you turn it. A burner ring fades on in white or blue over about 2 seconds, and fades off over about 1 second when you turn the knob off. The knob tic, listed separately, switches hard on and hard off. 1

The 7 Series manual treats the lighting as a feature with its own page, and it describes it in short rules rather than paragraphs. This guide turns those rules into things you can see in your kitchen. It covers the everyday behavior; the one state that is not everyday, the red error signal, has its own guide: what a red backlight and flashing rings mean.

KnobRingTic
BurnerFades on (white or blue) in 2 seconds when turned on; fades off in 1 second when turned offHard on, hard off
Griddle or gas ovenSame fade, plus a pulse during preheat until the first temperature is reached, then solidHard on and off; cycles
Dual fuel oven selectorFades on in 2 seconds and off in 1 second; pulses during preheatHard on when turned on, hard off when turned off
Dual fuel oven temperatureFades on and off the same way; pulses out of phase with the selector until preheatedHard on and off; cycles (the cycle light)

How do I change the light color?#

Reach under the bullnose and hold the number 2 button. The backlight cycles between blue, white and off, and you release it when you reach the one you want. On a range the two buttons are on the right side; on a rangetop they are on the left. 1

The manual's range features page also names a Lighted Bezel Switch: to change the color of the bezel light, hold the switch until the color changes and then release it. Both descriptions point to the same idea: hold, watch the color move, release. 1

  1. 1

    Find the buttons#

    Feel under the front bullnose of the range, on the right side. Buttons 1 and 2 are there. On a rangetop they are on the left. 1

    A fingertip presses a small button under the front edge of a range while the knob rings glow amber.
  2. 2

    Hold button 2#

    Keep it pressed. The backlight cycles between blue, white and off. 1

  3. 3

    Release at your color#

    Let go when the color you want shows, or when the lights are off. 1

  4. 4

    Test with a knob#

    Turn a burner knob on and off to see the fade in the color you picked. 1

An important detail: the error code still functions when the color is cycled to off. So a dark ring is a choice, not a way to silence an error. 1

What does the night light switch do?#

Button 1 turns on all the bezel backlights. When the night light is on, every ring behind the knobs shows your preselected light color, whether or not a burner is on. It exists so you can see the controls in a dark kitchen. 1

The manual's features page describes the Night Light Switch the same way: when it is in the on position, all of the rings behind the knobs display the user's preselected color. If you want the rings dark while cooking, set the color to off with button 2 and leave the night light off. 1

Why are my rings lit when nothing is on?#

Most likely the night light is switched on. Check button 1 under the bullnose. If every ring glows evenly in your chosen color and the range is otherwise idle, that matches the printed behavior. A red glow or a flashing ring is different and is covered in our guide linked above. 1

What is the pulse during preheat?#

On a griddle or gas oven knob, the ring pulses until the temperature is first reached, then stays solid until you turn the knob off. On a dual fuel oven, the selector ring and the temperature ring pulse 180 degrees out of phase until the first target temperature, then both go solid. 1

Think of the pulse as the oven telling you it is not ready. A solid ring says the target has been reached once. After that, the oven can still cycle its heat to hold temperature, and the manual describes a separate light for that: the temperature knob tic, the cycle light, goes hard on and off as the oven cycles. 1

For cooking, the practical rule is to wait for the solid ring before you put food in. The oven preheat rules for individual modes are in the oven section of the manual.

How does the griddle show its thermostat?#

The optional 15,000 BTU griddle or grill has an electronic thermostat to keep an even temperature once the knob is set. The bezel behind the knob cycles on and off as needed, and the manual says that is how it indicates the thermostat is maintaining the selected temperature. 1

So a blinking bezel on the griddle during a pancake breakfast is the working signal. The griddle section also reminds you to preheat on medium and then reduce heat if needed, to use only plastic, rubber or wooden tools on the non-stick surface, and to drain grease away from the burners with the burners off. 1

What do yellow and the cooldown look like?#

During self-clean the backlight is yellow, and the selector and temperature rings pulse during the preheat, then go solid. When the door unlocks after the cooldown, the rings revert to Viking blue until you turn the knobs off. 1

The manual also notes that if one oven is in self-clean, the other will not start self-clean. If you try, only the selector indicator lights, the temperature indicator does not, and the backlights come on without pulsing, which shows that the second oven has not started its preheat. 1 This is the light pattern of a refused start, not an error. Our self-clean problems page and the preparation guide cover the rest.

When are the lights a reason to book?#

When a ring does not light at all, never fades out, or glows red with flashing. A lit ring that behaves as described above is information. One that does not match the table is worth a look.

  • A burner ring that stays dark when the knob is on.
  • A ring that stays lit after the knob is off.
  • A red backlight and a flashing griddle or oven ring.
  • A cycling bezel on the griddle that never settles.

The backlit knobs entry covers the part, and our range repair page shows the kinds of jobs we take on.

What do I tell the technician about the glow?#

Describe the knob, the color and the motion in plain words: which knob, which color, steady or pulsing or flashing, and whether turning the knob off changed it. A short phone video of the ring is ideal.

Sources#

  1. Use & Care / Professional Freestanding Ranges / Built-In RangetopsViking Range, LLC (official manual PDF) · form 066424-000 (103122) · PDF p.10-12, 15 (Night Light Switch, Lighted Bezel Switch, Backlit Knob Features, griddle)

Here to help

Good questions.
Clear answers.

Talk to our team
Can I change the color of the knob lights?

Yes. Hold the number 2 button under the bullnose and the backlight cycles between blue, white and off. Release it when you reach the color you want. The buttons sit on the right on a range and on the left on a rangetop. [1]

What does the night light switch do?

Button 1 turns all the bezel backlights on, so every ring behind the knobs shows your preselected light color. It is a convenience light for a dark kitchen, not a cooking function. [1]

Why does the ring pulse before it goes solid?

On a griddle or oven knob the ring pulses until the first target temperature is reached, then stays solid until you turn the knob off. On a dual fuel oven, the two rings pulse 180 degrees apart. [1]

What is the knob tic?

The manual lists a knob tic beside the ring and says it goes hard on and off, and on oven knobs it cycles. It does not define the term further, so we only repeat what is printed. [1]

Do the lights fade or switch instantly?

Rings fade on over 2 seconds when you turn a knob on and fade off over 1 second when you turn it off. The tic, by contrast, is described as hard on and hard off. [1]

Let’s take care of it.

The burner will not light.
Let us take a look.